![]() ![]() For a simple install just plug it into the 12v lighter port. It really is easy once you have the right tools and a plan in place to route the wires. Take it slow and install your dash cam yourself. Small size footprint to mount in front of the rear vision mirror if required.If set up and hard-wired, any bump or motion will trigger the recording mode. Auto Parking Mode (Impact + Motion Detection).High Lux Security LED to warn passers-by they are under surveillance.Will not completely drain the car battery on the detection of a preset car battery voltage. Most of the features are still there like It’s good to see Itronics making a budget camera and not skimping on features. With its 120′ field of view, it’s wide enough to capture the whole road in front of you. If I need some video footage it’s just a simple procedure to remove the 32G SD card and download the required footage. I have no real use for the WIFI or rear vision at this time. You will still be able to read license plates at this quality and you can save some money at the same time. I have had no problems with it in the last 4 years.Įven though it records in 720p which is a slight step down in quality from the Itronics 100SPW which is 1080p. I have the older Itronics iPass Black ITB-200L dashcam which at the time it was one of the more reliable budget dash cameras on the market. It sure has a lot of high-definition recording options. Dual recording mode captures a crystal clear in the front and 1920x1080P 30fps inside the cabin or rear. You will get three recordings: Front, back, and inside the car.ġ440P+1080P+1080P at 30fps, which gives you full-round protection when you’re on the roads. It is considered one of the best on the market for 2020. The Vantrue N4 Dual Dash Cam 3 Channel 1440P Front & 1080P Inside & 1080P Rear. When you turn off the car the dashcam will stop. Now when you turn on the car the Itronics Dash Camera will start. You may have to reprogram your radio stations. Install the Radio fuse back in the mini blade as well, and test that it all works. This can be done using a crimp lug and bolt. A 2 amp fuse is fine for the truck dash camera unit. Install the piggyback mini blade holder and crimp the tail to the positive cable on the car dash cam. The negative can be attached to the frame somewhere under the dash to provide the earth or negative. Locate the radio fuse and pull it, and install the double fuse joiner in its place. Splicing into your fuse box is easy and will require a double fuse mini blade. So when you start the car the dash cm starts up as well. A simple method for auto-on is to splice it into the radio/cd player aux circuit. So we do not recommend this unless you use the car every day. You can set up the Itronics 100HD camera to be always on, and trigger recording on movement, but it will deplete your battery after a few days if you don’t use the car. This is so that when the car starts the dashcam will start up automatically. Next, I needed power 12v for the car cam. The manual will give you hints on how to remove your trim pillars and repair car headliner. I would recommend getting a workshop manual from eBay or Amazon for your car. This required pulling apart both the pillar and roof covers a little to pass the cable through.īe careful if you have side airbags on the pillars as you will need to route the cable in a place where they will not obstruct the airbags if they go off. The dashcam supple 12v cable was run through the ceiling headliner cover mat and down the right of the driver’s pillar garnish. This is a very tidy install and most people don’t even notice there is a dash cam installed. ![]() Once the dash cam is stuck with the 3m tape, it’s not coming off in a hurry. Remember to leave enough room to be able to adjust the rear vision mirror with the cam installed. The car camera is mounted with double-sided 3m tape that was supplied with the dashcam. To keep it out from obstructing the view of the driver. I mounted my itronics 100hd Dash Cam in front of the rear vision mirror for 2 reasons. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |